In the bent-over row you hinge the torso forward and pull the bar toward your midsection. It is one of the most complete back exercises, because it works from the upper back down to the lower back at the same time.
The trade-off is that the lower back is holding the hinged torso from start to finish. That is why posture matters more than the load.
Quick summary
- Muscles: back (lats and upper back), with help from the biceps; the lower back works to hold the torso
- Level: intermediate
- Equipment: a barbell and plates
How to do the bent-over row
- Stand with your feet hip-width apart and hold the bar with your hands about shoulder-width, palms down.
- Bend your knees a little and send the hips back, hinging the torso forward with a straight back.
- Let the bar hang with your arms straight, close to your legs.
- Pull the bar toward the lower chest or the navel, driving the elbows back.
- Lower under control until your arms are straight, without changing the torso angle.
Common mistakes
- The back rounding. If the lower back curves to pull, the load has gone too far. Reduce it.
- The torso rising on every rep. Using body momentum takes the work away from the back. The hinge stays still.
- Pulling only with the arms. Think about driving the elbows back and bringing the shoulder blades together at the end.
- The neck thrown up. The gaze stays a little ahead on the floor, with the neck in line.
Variations
Easier
The inverted row, where the body hangs under a sturdy bar. Or a supported row, with one hand on a bench and a dumbbell in the other.
Standard
Barbell bent-over row, palms down.
Harder
An underhand grip (palms up, as in the illustration below) or more load, always without losing posture.


What the studies show
A study with 7 healthy men compared three rows. The bent-over row activated the back a lot, from the upper back down to the lower back, but it was also the one that loaded the spine the most. The inverted row activated the lats and the upper back more, with the lowest load on the lower back (Fenwick and colleagues, 2009). If the lower back bothers you, the inverted row is the simplest swap.
Sets to start with
For beginners, the American College of Sports Medicine position stand suggests a load that allows 8 to 12 reps, 2 to 3 times a week. When you can do 1 or 2 more reps than planned, increase the load a little: the document talks about 2% to 10% (ACSM, 2009).
In practice, 2 to 3 sets with 1 to 2 minutes of rest are a good starting point. That number of sets is a practical suggestion, not a rule.
Who should be careful
Anyone with lower-back pain, a herniated disc or recent spinal surgery should talk to a doctor or physical therapist before doing loaded bent-over rows. Pain that radiates down the leg, tingling or sharp pain are signals to stop and get assessed.
Informational text. It doesn’t replace an assessment by a certified trainer, physical therapist or doctor.
Read also
- Plank: how long to hold it and how to do it
- Glute bridge: how to do it at home and progress to the hip thrust
- Training: exercises, home gear and books
Where to go next
A strong back helps almost everything else in the workout. To turn that into muscle, food counts as much as the set: see building muscle.
References
- Fenwick CM et al. Comparison of different rowing exercises: trunk muscle activation and lumbar spine motion, load, and stiffness. J Strength Cond Res. 2009;23(5):1408-17. https://pubmed.ncbi.nlm.nih.gov/19620925/
- American College of Sports Medicine. American College of Sports Medicine position stand. Progression models in resistance training for healthy adults. Med Sci Sports Exerc. 2009;41(3):687-708. https://pubmed.ncbi.nlm.nih.gov/19204579/
Image credits
- Everkinetic 0026 (reverse-grips-bent-over-barbell-rows) illustration, by Greg Priday / Everkinetic project — https://github.com/everkinetic/data — CC BY-SA 4.0. Used without changes.